AUTONET TV

Do you have a Clue (Get the Most Out of a Service Visit)

When you head to the doctor, you probably have it in your mind what you're going to say about why you don't feel good.  That way your doctor can use that information to diagnose your problem. You might want to think of that same approach when you take your vehicle in for a repair.

Experts say what will help the service advisor most is for you to bring in some well-organized descriptions about your vehicle's issues.  You might even want to write them down so you don't forget.  Is there an unusual smell?  What does it smell like?  Does the problem happen first thing after starting out? If there's an odd sound you hear, is it dependent on speed?  Does it change when you turn a corner?  

Keep your expectations realistic.  Some conditions may take a long time to diagnose and repair.  If you go thinking you'll be in and out in no time, you might be disappointed when you're told there are other customers ahead of you and you may have to come back tomorrow.  If you can make alternate plans to have someone pick you up and take you back when the vehicle is finished, that way you won't feel like you've wasted your time. 

Most importantly, be available for any communication from the service advisor.  If they have your cell phone and they have a question or need an approval for a repair, the sooner they reach you, the sooner things can move forward. 

The service facility wants your experience with them to be good just as you do.  With a little help from you, they'll get your vehicle back on the road and you'll have a smile on your face.

Economy Transmission and Auto Repair
201 Terryville Road
Bristol, CT 06010
8605891255

Start Me Up (Ignition Systems)

When you start up your gasoline engine car, you may not know that it's using the same ignition principles as it has for decades.  You have spark plugs that require enough power so a spark can jump across a gap at its tip.  Years ago, a vehicle's 12-volt system had to produce 15,000-25,000 volts to do that, so engineers came up with something called an ignition coil that bumps up the voltage. It also has to be done at just the right interval called timing.

The first systems had a distributor, a mechanical device with a rotating disc that switched the power to the ignition coil on and off.  That higher voltage then was sent to the spark plugs at the correct time interval. But the mechanical "points" had to be replaced and adjusted every 12,000 miles/20,000 kilometers.  Engineers later replaced the switching mechanism with solid state ones, but they still needed replacement after 120,000 miles/200,000 kilometers.

The next evolution came in the 80's when the distributor was replaced with a couple of sensors which talked to a computer.  This "DIS" (distributor-less automotive ignition system) was a big advance.  Plus, it didn't use just one ignition coil for all the cylinders.  It had coil "packs" that each provided spark to two cylinders.  That way, the voltage could be boosted even higher, to 30,000 volts, which helped engines be able to ignite a leaner fuel/air mixture.

Recently have come even more improvements.  Now instead of coil packs, there's a coil that's attached to each spark plug.  No more spark plug wires means less maintenance. Plus, a stronger, hotter spark of 50,000 volts can make an engine more reliable, increase fuel economy and reduce emissions.

No matter what ignition system your vehicle uses, your vehicle service facility has a staff of technicians trained to work on the latest technology.  Make sure to have your vehicle maintained regularly so you can take full advantage of these modern engineering marvels.

Economy Transmission and Auto Repair
201 Terryville Road
Bristol, CT 06010
8605891255

Have a Ball! Know your Ball Joints (Ball Joints)

We all have joints in our own skeletal system, but did you know your vehicle has some joints of its own? One of the most important is called a ball joint.

One of the interesting things is that it's somewhat similar to the ball and socket joints we have in our hips and shoulders.  A ball joint allows two parts it joins together to move in more than one direction at the same time.

Think about your wheels.  They have to move up and down when there are bumps in the road but in sideways directions when you are making a turn. As you can see, the ball joints are important for your steering and handling to work correctly.

Since ball joints do so much, they can wear out and become loose.  When the ball wears down or the socket gets worn, there can be too much play in them.  It can get so bad that the ball can come out of the socket and your wheel can fall off, a dangerous situation.  Ball joints can also seize up.  Some of them are sealed and never require maintenance; others require periodic lubrication.

Here are some signs that your ball joints are going bad:

• Your vehicle pulls to one side
• You can hear a clunking noise coming from a wheel area
• Your tires are wearing unevenly, especially on the inside

The earlier a failing ball joint is discovered, the better. The best way is to have regular inspections by a technician.  Your service facility will periodically check ball joints at intervals recommended by the manufacturer. The cost to replace them can vary widely depending on whether you have a vehicle with a 2-ball or 4-ball configuration.  Also, sometimes just the joints can be replaced, but other times they are part of a larger control arm assembly that has to have all the parts replaced at the same time. 

Your vehicle's proper steering, handling and tire wear all contribute to a better, safer driving experience.  Make sure your ball joints are up to the job.

Economy Transmission and Auto Repair
201 Terryville Road
Bristol, CT 06010
8605891255

Passing the Test (How to Prevent Emissions Test Failure)

Vehicle emission testing has become ubiquitous in North America and for a good reason.  Clean air quality is important for the environment and all of us.  Since vehicle emissions are among the main causes of air pollution, emission testing can alert you to problems in your vehicle than can be fixed so it won't needlessly pollute.

Emissions tests are looking for certain toxic gases internal combustion engines produce, such as nitrogen oxide, particulate matter, non-methane organic gases and formaldehyde.  Emissions control systems reduce these gases if they are working properly. 

The best way to minimize pollution is to keep those vehicle systems working properly, and periodic inspection and maintenance is the key.  So if you want to make sure your vehicle will pass an emissions test, it helps to know what might go wrong.

Let's start on the easy one.  Your gas cap could be loose, allowing vapors to escape into the atmosphere.  The most common solution is to replace it.  Or your air filter may be dirty.  A dirty air filter may push your hydrocarbons pass the acceptable level.

Now to the more complicated things.  The mixture of fuel and air in your engine may be tilted toward the "too much fuel" side.  That could cause problems for your vehicle's catalytic converter, a device that converts toxic gases from your exhaust into less toxic pollutants.

Your vehicle has a closed system that prevents fuel tank vapors from escaping into the air; it's called the EVAP system.  A technician can track down problems.

Vehicle engineers have gone to great lengths to minimize the amount of pollution your vehicle produces.  Your vehicle's manufacturer recommends how frequently those systems need servicing.  Keep those systems in good shape and you're likely to pass emissions tests with flying colors.  Neglect them and you might find your vehicle failing an emissions test.  When that happens, you'll have to get the problems repaired before you can get back on the road.

Economy Transmission and Auto Repair
201 Terryville Road
Bristol, CT 06010
8605891255